Jump to content
Please check your junk folder for registration emails ×
  • Current Donation Goals

    • Raised $0.00

ZS Sequential Controller


B4 I was 250T

Recommended Posts

I'm sure we have guys who have/ have had these. What can people tell me about them please? Can you select change overs depending on which gear or is it set change over point once and that's it for all gears? Anyone have a recommended RPM point to set secondary to or is it individual? Any, any, any info advice, tips, info would be much appreciated. Cheers

Link to comment
Share on other sites

  • Admin

Changeover is purely for rpm, doesn't know what gear you're in. I used to set it about 400rpm higher than stock. Mainly because i used to end up changing down into the dead zone when giving it a bit of a rev which just killed all the fun

Link to comment
Share on other sites

You can set the single turbo-twin turbo changeover point up to 5000rpm. Then also set the twin turbo-single turbo return changeover RPM, IIRC as low as 4000 RPM.

I used mine the same as Andy, making it stay in primary mode longer. Setting the single/twin change as late as possible (5000rpm), so you can change gear later without hitting VOD driving around town. Also have more torque at the changeover, higher RPM and more exhaust flow.

Then set the return from twin-single as low as possible (4000rpm), so that it stays in twin turbo mode longer. Then when it gets below 4000rpm it changes back to single turbo.

Here's the original wiring diagram:

http://download.robson-brown.co.uk/uklegacy/zerosport/02wiring.jpg

Here's a pic of what it will look like wired in. Note ECU wires 1-5 dont get cut, they get spliced into/tapped into:

Zerosports_fix.png

The ECU wires you'll be splicing/linking into, at the bottom of this page (BH/BE5A/B/C)

http://download.robson-brown.co.uk/uklegacy/zerosport/03plugs1.jpg

Full install instructions:

http://download.robson-brown.co.uk/uklegacy/zerosport/index.html

ECU pinout for the BE-BH5A/B/C, including ECU wire colours for double checking:

http://www.brdevelopments.com/docs/MY99%20Legacy%20TwinTurbo%20ECU%20pinout.pdf

ECU pinouts found here:

http://www.brdevelopments.com/archive.html

All covered a bit more in this thread:

http://clubsub.org.nz/forum/showthread.php?43601-Zerosports-Sequential-Boost-Controller-Issue/page7&highlight=zerosports+sequential

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recent Status Updates

    • MrSg9Sti04

      Afternoon team,
      im new to the group first time posting. Im hoping some body can help me get my launch control all dialled in on my link g4x. Ive had the computer and car all tuned from chris at prestige awesome knowlegable guy super happy with the results but now im wanting to get my launch/anti lag all dialled in. Ive been reading multiple different forums etc all with different conflicking information which has made me nervious with what do i listen to this or that if you get what i mean. Now ive started to make myself familiar with my PClink software etc the past few weeks and im eager to learn how to do minor setups or tweaks etc so im not relieing on my tuner so much and obviously saving myself abit hurt in the back pocket. 
      Now back to the question at hand.... Im wondering if theres and one who could please share there knowledge and wisdom with setting all my values, timing, fuel etc when i have launch control armed and engaged, or even a launch tune file they can possibly send me to load onto my tune. Ive figured out the setup of my digital inputs turning launch control on etc and its obvisously on its pre set factory settings. It engages but doesnt sound the greatest or as angry as it should i feel. Hence reaching out to you good buggers. 
       
      Cheers in advance for any info and help yous maybe able to give me.
       
      Cheers Shaun
      · 0 replies
    • Joker  »  gotasuby

      updated your DP's too : hope that's ok!
      · 0 replies
    • Joker  »  SAS

      Updated your DP's to reflect your business page  
      · 0 replies
    • Joker  »  Nachoooo

      Updated your Avatar : couldnt help myself  cheers!
      · 0 replies
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    40.9k
    Total Topics
    573.5k
    Total Posts


×
×
  • Create New...