Technikhaus

Yeah our old 2011 STI we put the R400 and a PBMS Catless downpipe onto. Definitely was far too loud, but our local mechanic always passed it, VTNZ etc would fail it for certain.

Man that's awesome to hear, happy for you!

Sold the Gravel Express last night, definitely going to miss it! Gone to an enthusiast in Queenstown though, so should be well enjoyed and looked after.

I haven't personally, but I think it all depends on what model you're wanting to import. Most of the pre-2000s would be harder to import now due to emissions, and some of the mid 2000s ones would need to be 'special interest' I believe?

Dunedin too, good old NPD 284.6 for 100 at npd 315.9 for 98 at BP

It's not an STI, but it may as well be 😛 6 Speed manual, fully forged motor, ported &polished heads, GTX3071R. https://www.trademe.co.nz/a/motors/cars/subaru/listing/3480897035?bof=cxkFWEkT

Yeah, I needed some gearbox seals for the six speed, bought off of both Amayama, and Partsouq, and also bought what the dealer had in stock locally, so have a couple of spares now lol

Yeah we have to give the LVVTA guys a hell of a lot of respect for everything they do for keeping the laws in check. They have some interesting posts on facebook that went over how they were setup, and everything they actually do. If it wasn't for that group then we wouldn't be allowed to do anything at all to our cars. Let alone what we can do without a cert.

Oh and how you can't add a valve to an exhaust, but OEM can have them... hate that one.

I find these rules funny to be honest. I used nite-shades on my FTO many years back, and never had an issue with WOFs etc, but another friend with the same car immediately failed his WOF for it. And also, if it's factory, it's okay 🤷‍♂️. My new car has them as a factory option (only photo I have that shows them, but they're the factory-option tinted taillights.

I have the full whiteline bushings and bump steer kit. What did you do about the engineers report for that? Hadn't even thought of that. Has Bilstein suspension and some springs, no adjustable suspension or aftermarket sway bars etc.

Hey team, So I was just thinking, I'd like to try for a cert at some point this year, but I'd like to be as prepared as possible. I know there's a few here that have gone through the process, what are somethings that you should always check first, like the simple failures. Off the top of my head I can think of: Heat shielding/blanket around turbo. Driveshaft hoops? This one always gets me, unsure when they're required, and if it's in the front or rear half of the shaft? Brake lines secured Not looking for advice as such (I know, talk to your cert guy). But just little things that people have been picked up on that I could easily check before even going to the certifier. My mods for reference: Engine power increase to 300whp Aftermarket turbo Aftermarket ECU Automatic to 6sp manual swap Front and rear brake upgrade (To BL/BP larger rotors - 2/1 pot calipers) 17" wheels They're the main items I think. So off the top of my head I need to put a heat shield on the turbo, and secure the TMIC better, but can't think of other things? Not sure if Brake Bias would be affected with the larger brakes, and whether that'd be an issue.

Thankfully don't have one in there anymore 🤣

Link branded MAP sensor in the engine bay, and Link CAN-Lambda sensors. If I just cover them they'd not know. haha

Yeah WOF failures are so hit and miss. I had an FTO that for ~5 years had no issue passing WOFs with the wheel/tyre combo it had, until one day it failed on being above the 5% tolerance on tyre size increases. It was about 5.2%. The same also goes for a 5 -> 6 speed manual swap as well. Aftermarket ECUs too area another good one that sometimes gets let through, sometimes not